Known Issues

  1. Call conference only works with 3 way calling on hard phones.  Soft phones can reportedly handle up to 10 simultaneous calls
  2. Currently it is not possible to automatically hit dial and successfully call a number from the Caller ID list - these must be redialed manually.

 

Key Training Issues

  1. BUTTONS DO NOT DIAL AS YOU PUSH THEM:
    • It’s almost like email: when you enter a phone number the system then “SENDS” the phone number to connect you. 
    • The phones are sensitive to the TIMING of your pushing the buttons.  Dialing 3 or 4 digits and then pausing can result in a failed cal.  
    • To control this you can change the delay before dialing preferences setting.
  2. BLIND vs MANAGED call Transferring
  3. RING OUT
  4. FIND ME FOLLOW ME
     

 Pending Configuration Items

  1. Outbound call forwarding setup

 

IP Phone User Guide - Mailbox, Mute and Hold Buttons

Dialing a Telephone Number

Activate a dial-tone prompt one of four ways:

·         Lifting the headset

·         Press the speaker button

·         Press an empty line button

·         Press the headset button (only when a headset is connected)

Enter the phone number using your phone keypad. You will see Calling and Connected in sequence as the call is being connected. At the end of the call, hang up the phone to disconnect. For a headset or speaker, you must also push the X button to end the call.

Please Note: Enter 1+ the 10 digit number when dialing long distance

Muting a Call

Mute the handset, headset or speakerphone by pressing the mute button. This prevents the person on the active call from hearing what you or someone else in the room is saying. To cancel the mute function press the mute button again

NOTE: On the 300 series the mute button is the bottom of the 6 right buttons

Dialing a Phone Directory Listing

To access local phones Directory Press the directory softkey. Scroll down until you find the number you wish to call, press the dial softkey.

NOTE: On the 300 series the directory button is the third from the bottom of the 6 right buttons

Redial

To see a list of recent calls made, press the redial soft button. Scroll down until you find the number you wish to call, press the dial softkey.

NOTE: On the 300 series the redial button is the fourth from the bottom of the 6 right buttons

Three way conference calls

To initiate a conference call, put the current call on hold by pressing the hold softkey (this can also be done by directly picking up a new line). Pick up an empty line and dial the second persons telephone number. You will be talking privately to the second party when he/she picks up. (First call remains on hold) TO start the conference press the conference softkey. All three parties will now be participating in a conference call.

NOTE: If you hang up the other two parties will be disconnected

NOTE: The 300 series does not support local conference calls

Placing a Call on Hold

Press the hold button to put the active call on hold. If there is another incoming call you can now answer the 2nd call

Resume the 1st call by pressing the line button associated with the 1st call. If the 2nd call is still in progress it will automatically go into the hold state when the 1st call becomes active.

NOTE: On the 300 series you must press ## to put a caller on hold

 

Transfer a caller

Please Note: There are two kinds of transfers. Blind and Managed. Your phone system can handle both.

·         A managed transfer is when the call is announced to the call receiver before the transfer is made.

·         A blind transfer is when the call is transferred to the transfer receiver without notifying the receiver of the transfer first.

 

 

NOTE: On the 300 series the transfer button is the second from the bottom of the 6 right buttons

 

 

Managed Transfer to an extension

TEMPORARY WORK AROUND:

During a call first put a person on hold by pressing ##. Then Proceed normally as below:

During a call first put a person on hold by pressing the hold button. Pick up a new line and call the extension you wish to transfer the call to.

When ready press the transfer button twice. You can hang up any time after the transfer.

 

Blind Transfer to an extension

During a call press ## + Extension Number

Note: Make sure to wait until the transfer is complete and the line hangs up on your phone before hanging up, otherwise the transfer will not be completed.

 

Blind Transfer to a non extension

During a call press ##. Then press * + 1 + phone number + #

Your call will now be transferred. You can remain on the line to introduce the transferred call to the next number. Hang up at any time to complete the transfer or, to cancel the transfer press **

Note: Make sure to wait until the transfer is complete and the line hangs up on your phone before hanging up, otherwise the transfer will not be completed.

 

Phone Directory Setup

For numbers you call often you may want to set up a personal directory. To add entries to your personal directory please follow these instructions:

·         Press the directory softkey

·         Select <New Item> pres the key below the 6 dots on the screen

·         Enter  a name and press the check softkey

·         Enter a number and press the check softkey

·         You will be bounced back to the main directory. You can now call using the directory

Ring Tone

To change the default ring tone please follow the instructions below.

·         Press the menu softkey

·         Select line and press the check softkey

·         Ringtone and press the check softkey

·         Select the identity and press the check softkey (typically there will be only one identity per phone)

·         Scroll  though the ringers and select the one that you prefer by highlighting it and pressing the check softkey

·         Press X repeatedly until you are back outside the menu

Accessing the voice mailbox

Access the voice mailbox by pressing * + Password + # +1

·         replay press 1

·         save press 2

·         erase press 3

·         return the call press 4

·         forward the message to an extension press 5

·         skip the message press 6

Change Default Voicemail Recording over the Phone

To record your Voicemail Greeting over the phone, please follow the directions below:

  • Call your Ring Central number (646) 233-0653

     

  • Enter your extension XX

     

  • At any time, press the Star key (*)

     

  • Enter your password followed by the Pound key (#)(default password is 97531)

     

  • Press 2

     

  • Press 2

     

  • Listen for the rule Business Hours and select it when prompted

     

  • Press 2 and follow the instructions

     

Change Spoken Name Recording over the Phone

To record your Voice Name over the phone, please follow the directions below:

  • Call your Ring Central number (646) 233-0653

     

  • Enter your extension XX

     

  • At the prompt, press the Star key (*)

     

  • Enter your password followed by the Pound key (#)(default password is 97531)

     

  • Press 2

     

  • Press 1 and follow the instructions